Ridge ventilation
Every wall, chimney and pipe gets new flashing, and a ridge vent caps the peak which is where most leaks would otherwise start.
Shingle Roofing
Shingle Roof Installation New Milford, NJ
A New Milford roofer can help you pick between 3-tab, architectural and impact-resistant shingles and install the full system beneath them, so the roof is sealed against wind-driven rain from the start. Call (551) 374-2044 to reach a local roofer.
Shingles are only the top layer of a shingle roof. Below the shingles go metal drip edge, a self-adhering ice barrier at the eaves and valleys, a layer of underlayment and a starter row at the edges. Then come the flashing details and the ventilation, which decide whether the roof stays dry and how long the shingles last.
The first decision is the shingle itself. 3-tab shingles are thin and uniform, and architectural shingles are thicker laminated shingles with a textured, shadowed look and higher wind ratings. Impact-resistant shingles rated Class 4 under the UL 2218 test are an option where hail is common, and some insurers treat them differently, so ask yours.
Shingles are made for sloped roofs. Below a 2 in 12 slope, water moves too slowly for shingles, so low sections get a membrane roof instead. Flat sections are flagged during the estimate so the right material goes on each part.
Depending on what the roofer finds, shingle roof installation in New Milford, NJ can go hand in hand with shingle roof replacement and roof installation.
Need shingle roof installation in New Milford? Call (551) 374-2044 and describe the problem to a roofer who works in New Milford.
Call nowThe process
How shingle roof installation works
A shingle roof is built from the eaves up, layer over layer.
Start with the deck
Sheathing has to be flat, dry and well fastened, so loose sheets are renailed and damaged ones replaced. Shingles laid on a bad deck show every flaw.
Ice barrier first
The eaves get drip edge and a band of ice and water shield, and the valleys get a full-length strip. That membrane seals around nails where ice backs water up.
Lay the underlayment
The rest of the deck is covered in underlayment, lapped so each row sheds onto the one below, with rake drip edge on top. Most roofers now use synthetic, which resists tearing and lies flatter than felt.
Set the first course
Starter shingles go on first at the eaves and rakes, putting a sealant line under the edge where wind lifts first. Without it, the first course has nothing holding its lower edge.
Nail the courses
The field is shingled with correct offsets and nailing, with step flashing, kickout flashing and pipe boots set as the courses reach them. Valleys are finished open with metal or closed-cut, depending on the shingle and the roof.
Ridge vent
A ridge vent is cut in along the peak and capped with hip and ridge shingles, balanced with soffit intake at the eaves. Balanced airflow keeps the attic cooler and drier and helps the shingles last.
What is included
Layers of a shingle roof system
Synthetic underlayment
The whole deck is covered with lapped underlayment as the second line of defense.
Drip edge
Drip edge and a sealed starter row protect the roof edges for a clean, sealed edge.
Eave membrane
Self-adhering membrane is applied at the eaves and in valleys beneath the underlayment and shingles.
Choosing a shingle
3-tab, architectural or impact-resistant shingles are matched to the house and to the weather the roof will face.
Related service
Architectural Shingle Installation New Milford, NJ
Architectural shingles go on over the same deck, underlayment and starter as any shingle, with their own nailing pattern. Each nail has to pass through both layers in the marked nailing zone, which is narrower than on a 3-tab shingle. The ridge and hips get thicker cap shingles made for the line, not cut 3-tab pieces.
For New Milford homeowners, architectural shingle installation has become the default for new roofs. Their weight and laminated build give them higher wind ratings and a longer life. Look at a few colors on a nearby roof in daylight before deciding.
Related service
Asphalt Shingle Roof Installation New Milford, NJ
An asphalt shingle roof installation is the most common way to roof a house, and the details decide how well it performs. Most early leaks on new shingle roofs come from flashing, nailing or missing starter, not from the shingles. It is fair to ask which underlayment and ice barrier will go on and where.
For an asphalt shingle roof installation in New Milford, plan for a few days of work on an average house. In cool months the sealant strips take longer to bond, and the edges get extra attention. The crew will watch the forecast, since wet decking cannot be covered.
Local help
Shingle Roof Installation Near Me
In New Milford, asphalt shingles remain the most common choice for new residential roofs. Older homes in New Milford and nearby towns like River Edge, Bergenfield, Dumont and Oradell often had felt underlayment and box vents, while new roofs usually get synthetic underlayment, ice barrier at the eaves and a ridge vent, which is why the system under the shingles deserves as much attention as the color. Looking for a shingle roofer near me? Ask about the full system, from drip edge to ridge.
Searching for shingle roof installation near me from New Milford or River Edge, Bergenfield, Dumont and Oradell? Call (551) 374-2044 to talk to a roofer who works in your part of town.
What the local climate does to a roof
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in New Milford is busiest after a hard winter and before the next one.
Why call
Why fix it now
Less damage
Small roof problems caught early usually stay small repairs.
Local knowledge
Roofers in New Milford know the roof types and weather wear common in local homes.
Clear next steps
Ask the roofer about the cause, the options and the estimate before work starts.
Shingle Roof Installation questions
How steep does a roof need to be for shingles?
The usual minimum for shingles is a pitch of 2 in 12. Roofs that are low but still within range get added underlayment protection. Porches and additions below that line need a low slope material.
Can shingles be installed in cold weather?
Mild, dry weather is the easiest time to install shingles. In cold weather shingles get stiff and the sealant strips need sun to bond, so roofers handle them carefully and often hand seal the edges. Rain and snow are the real limits, since a wet deck should never be covered.
What kind of underlayment should go under shingles?
Under the shingles sit drip edge, a self-adhering ice barrier in the leak-prone areas, a full layer of underlayment and starter shingles. Most roofers now use synthetic underlayment instead of felt, since it lies flat and resists tearing. The shingle instructions and local code set the minimum.
What is the difference between 3-tab and architectural shingles?
The difference is construction: one flat layer for 3-tab, two laminated layers for architectural. Architectural shingles generally have higher wind ratings, last longer and have a textured look, which is why most new roofs use them. 3-tab still works for sheds, garages or matching an existing roof.
Why does nail placement matter on a shingle roof?
Nailing is what holds shingles down until the sealant bonds and long after. Four nails per shingle is common, with six where the shingle instructions or local code call for high-wind nailing. Each nail has to sit in the nailing zone, flush with the surface, not too high and not driven through.
More questions? Call (551) 374-2044
Related services
Shingle Roof Replacement
Tearing off a worn shingle roof down to the decking and putting on a new one, so the new roof starts on a sound, dry deck.
Learn moreRoof Installation
New roof installation done in the right order with the right details, whether it is asphalt shingles, metal or another material.
Learn moreRoof Ventilation
Balancing attic intake and exhaust with soffit vents, ridge vents and attic fans, so shingles and decking last as long as they should.
Learn moreGutter Installation
Seamless gutter installation sized to the roof, pitched to the downspouts and hung on hidden hangers, from K-style aluminum to half-round and copper.
Learn more
Looking for something else?
See all roofing servicesGet shingle roof installation help in New Milford
Call now for New Milford shingle roof installation and help in the towns around it.