Tear-off
Decking is inspected and replaced where needed before new layers go down.
Flat Roofing
Rubber Roof Installation New Milford, NJ
A roofer in New Milford can install a rubber roof by laying EPDM membrane in wide sheets over insulation and a cover board, bonding or fastening it down and sealing every seam with primer and tape, and explain each choice before the sheet is rolled out. Call (551) 374-2044 to reach a local roofer.
Rubber roofing usually means EPDM, though some people use the term for any single-ply membrane. EPDM is sold in wide rolls, typically 45 or 60 mil thick, and it stretches and recovers as the roof moves through hot and cold seasons. Its seams are joined with primer and tape instead of hot air.
The first decision is how the membrane is held down. The sheet can be glued to the substrate, fastened with plates at the seams or laid loose under a layer of stone. On most homes, fully adhered EPDM is the usual choice because it handles wind well and stays smooth.
Then comes thickness and color. Thicker 60 mil membrane stands up better to foot traffic and hail. Black is standard and holds heat, while white reflects it. The transition to a steeper roof or a wall is planned with the same care, since that is where low roofs most often leak.
If the problem goes deeper than it first looked, a New Milford roofer may also recommend rubber roof repair or flat roof installation.
Need rubber roof installation in New Milford? Call (551) 374-2044 and describe the problem to a roofer who works in New Milford.
Call nowThe process
What happens during a rubber roof installation
Each layer is set up to give the membrane a smooth, solid base.
Deck prep
The deck is repaired and checked for slope, ideally a quarter inch per foot toward drains or gutters. A tear-off comes first on existing roofs.
Install insulation
Rigid insulation, often polyiso, is fastened with plates and screws, then a cover board goes on top. Tapered boards add slope where needed.
Lay the sheet
The membrane is unrolled, aligned and allowed to settle before bonding. Seam layout follows the direction of drainage.
Apply adhesive
Contact adhesive goes on the board and the membrane, and once it is tacky, the sheet is laid down and brushed. Then the other half is done the same way. Air pockets left under the sheet can turn into blisters later, so the crew works the rubber flat from the center out.
Seal the seams
Primer and seam tape join the sheets, with T-joints covered by extra patches. Lap sealant goes along exposed tape edges.
Finish the edges
Flashing goes up walls and around curbs, with boots at pipes and new edge metal at the perimeter. Termination bar and counter flashing seal the wall edge. Before the crew leaves, seams are probed for any loose spots.
What is included
What rubber roof installation covers
Rubber sheet
A 45 or 60 mil EPDM sheet is installed over a clean, dry base.
Cover board
Insulation adds energy savings and slope for a smooth surface.
Flashing
Every penetration and edge is sealed with materials made for EPDM.
Seam tape
Seams are primed, taped and rolled and is checked before closeout.
Related service
EPDM Roof Installation New Milford, NJ
The quality of an EPDM installation shows up years later in the seams and edges. The membrane has to lie flat on a clean, dry cover board, the adhesive has to reach the right tack before the sheet is laid and every seam has to be primed and rolled with care. Dry, mild days give the best bond. Different adhesives may be used in the field and at the flashings, each matched to the job it does.
A good New Milford installer also plans for movement. Perimeter securement and proper flashing help prevent the shrinkage problems older rubber roofs show. Ask how the roofer secures the perimeter.
Local help
Rubber Roof Installation Near Me
In New Milford, EPDM is a popular choice for low slope roofs on additions and attached garages. Across New Milford and nearby towns like River Edge, Bergenfield, Dumont and Oradell, EPDM handles storms, sun and cold well when it is installed with good seams and drainage, so installation details matter as much as the material.
Searching for rubber roof installation near me from New Milford or River Edge, Bergenfield, Dumont and Oradell? Call (551) 374-2044 to talk to a roofer who works in your part of town.
Roofs in this climate
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in New Milford is busiest after a hard winter and before the next one.
Why call
Why act early
Drier ceilings
Small roof problems caught early usually stay small repairs.
Familiar with local homes
Local roofers see the same roofs and storm damage across New Milford and nearby towns.
Clear next steps
Ask the roofer about the cause, the options and the estimate before work starts.
Common questions about rubber roof installation
Should my rubber roof be black or white?
Color affects heat gain. White helps in sunny climates, and black is common where winters are long. Ask about both options.
Can a rubber roof go over an existing roof?
A recover is possible only under certain conditions. Codes generally allow one recover over a dry, sound roof. Wet insulation or multiple layers mean a tear-off. Core samples or a moisture scan show whether the old roof is dry enough.
What is the lifespan of a new EPDM roof?
EPDM can last 25 years or longer. Regular inspections help it reach its full life. Repairs are simple when needed.
Which EPDM thickness should I choose?
The common choices are 45 mil and 60 mil. Sixty mil resists punctures better and lasts longer, which helps on roofs with foot traffic or hail. Even thicker sheets are available for demanding roofs.
Is a rubber roof the same as TPO?
They are related but not the same. Black EPDM is taped and stretchy, and white TPO is welded and reflective. Both are common on flat roofs.
More questions? Call (551) 374-2044
Often needed together
Rubber Roof Repair
Fixing open seams, punctures, shrinkage and split flashing on EPDM rubber roofs, never with tar or asphalt cement that ruins the rubber.
Learn moreFlat Roof Installation
Installing TPO, PVC, EPDM or modified bitumen roofs on additions, garages, porches and flat-roof homes, planned around how the roof will be used.
Learn moreTPO Roofing
TPO membrane roofs installed over new insulation or in place of a worn flat roof, sized to the deck, the drains and the way the roof is used.
Learn moreFlat Roof Replacement
Replacing old built-up, torch-down, EPDM or TPO roofs with a new system built to drain, with tapered insulation where water used to sit.
Learn more
Looking for something else?
See all roofing servicesTalk to a New Milford roofer about rubber roof installation
Call now for New Milford rubber roof installation and help in the towns around it.